Worker in a white protective suit and respirator vacuuming along an opened lower wall, a teal air scrubber and blue-taped plastic sheeting behind

Tempe, AZ · Emergency form open 24/7

Mold Removal Tempe, AZ

You can see mold, or you can smell it and cannot find it. Send the form day or night, and someone from our team will call you back soon. Testing, removal and clearance follow.

  • Form open 24/7
  • Tempe + 22 Valley cities
  • Testing, removal, clearance

Form open 24/7

Get a call back

Tempe · Maple-Ash · Mitchell Park · Escalante · University Park · Riverside + 29 more towns

01 / What you get

What you get when you send the form

Mold in a rental, a condo or an older Tempe house is usually a moisture problem wearing a disguise.

Mold removal in Tempe is three jobs, not one: find the moisture, remove the growth and the material it has colonized, then verify with clearance testing that the space is clean. Most mold here traces back to a monsoon roof leak, a condensate line dripping inside an attic air handler, a swamp cooler pan, or a slow supply line under a sink. National remediation ranges run about $1,500 to $9,000, with a typical job near $3,500 and small bathroom jobs starting around $500.

That is the short answer. The long answer covers the housing stock that makes mold common here, the difference between testing and removal, what the work costs by room and by square foot, the Arizona rules that matter, and the questions people ask before they book anything.

  • 01A call back from our team after you send the form
  • 02A plain read on what you see: test first, or remove
  • 03Moisture checked first, because mold returns when the water does
  • 04Clearance testing named as the last step of the job
Woman in a teal polo holding a tablet beside an air sampling pump on a tripod in a condo living room with a city skyline and a hill in the windows

03 / Symptom finder

What are you seeing?

Most people do not start with the word mold. They start with a smell, a stain, or a line of dark grout that came back after cleaning. Pick the closest description.

Symptom finder

Pick the sign that matches what you see

Likely service

Pick a sign above

Why

Each sign points to one service page. Choose the closest match.

If two or three of these fit, start with testing rather than guessing. A musty smell with nothing visible is a moisture question before it is a mold question, and the answer is usually found with a moisture meter and an air sample, not with a bottle of spray.

04 / How it works

How a mold job runs, step by step

The sequence is the same whether the job is a bathroom cabinet or an attic. What changes is the scale of the containment.

  1. Find the moisture

    A moisture meter and a thermal camera, not a guess. The source might be a roof detail, a condensate line, a supply line, a slab leak, or a failed exhaust fan. If the source is not identified, the job is not ready to start.
  2. Contain the area

    Plastic sheeting and negative air pressure keep spores out of the rest of the house. This is also when the scope gets photographed and documented for the owner, landlord or adjuster.
  3. Remove what cannot be cleaned

    Porous material that has been colonized comes out, bagged and removed. Non-porous material is cleaned. The goal is removal of the colony, not a coat of paint over it.
  4. Dry and clean

    The structure is dried to a measured moisture content, then HEPA vacuumed and wiped.
  5. Verify, then repair

    Clearance testing or a visual verification confirms the space is clean before reconstruction. Drywall, texture and paint come after.

After you send the form

  1. Send the form, day or night

    Say where the mold is, how big it looks and what changed before it appeared.
  2. Someone from our team calls you back

    You go over what you see, who owns the building and what has to happen first.
  3. Testing, removal and clearance follow

    The work runs in a fixed order and ends with a check that the space is clean.

05 / Not this

What mold removal is not

A few services get sold as mold removal but do not meet the definition.

  • 01

    It is not a spray-and-wipe

    A disinfectant or a "mold killer" applied to a surface does not reach the colony inside drywall, wood or insulation, and it does not fix the water. On a non-porous surface, cleaning can work. On a porous material, removal is the reliable answer.

  • 02

    It is not paint or sealer

    Paint can hide a stain without fixing the moisture, and the problem can show up again at the next wet season.

  • 03

    It is not an ozone machine and a closed door

    An ozone machine does not remove colonized material.

  • 04

    It is not a test-only visit

    Testing answers what is present. It does not remove anything.

  • 05

    It is not a promise to kill all mold permanently

    Moisture control is the permanent fix. Mold can return wherever moisture returns.

The useful definition is the boring one: find the water, contain the area, remove what cannot be cleaned, dry the structure, verify the result.

06 / Get a call back

Request a callback

The form asks what you need, how soon, whether you own the home, then how to reach you. Send it day or night, and someone from our team will call you back soon.

  1. 01What you need
  2. 02How soon
  3. 03Whether you own the home
  4. 04How to reach you

07 / Costs

What mold removal costs in Tempe

These are national ranges, not Tempe quotes. They come from one national cost guide to mold remediation, updated August 29, 2025, with a second national cost guide as a reference. Local pricing depends on access, containment, how much material has to be removed, and whether the moisture source is fixed before remediation starts.

By location, the national ranges look like this:

  • 01National rangeBathroom$500 to $1,500Caulk, grout, vanity base, shower surround, access
  • 02National rangeAttic$1,500 to $9,000Roof deck area, insulation removal, air handler platform
  • 03National rangeAC and ducts$3,000 to $10,000Duct runs, air handler, coil and plenum access
  • 04National rangeKitchen$1,200 to $10,000Cabinet base, under-sink wall, dishwasher and ice maker lines
  • 05National rangeWalls and ceilings$1,000 to $12,000Square footage of drywall, stud cleaning, texture and paint
  • 06National rangeWhole home$10,000 to $30,000Multiple rooms, HVAC involvement, full containment

By size, using the $10 to $30 per square foot range that one national cost guide reports:

Affected areaArithmetic rangeComment
50 sq ft$500 to $1,500A small bathroom or closet
100 sq ft$1,000 to $3,000A bathroom ceiling plus one wall
200 sq ft$2,000 to $6,000A room, or an attic platform
300 sq ft$3,000 to $9,000Several rooms or a full attic
500 sq ft$5,000 to $15,000A large open area with containment
1,000 sq ft$10,000 to $30,000Whole-home scale

A worked example. A 100 square foot bathroom ceiling with growth around the exhaust fan and one wall behind the shower: the arithmetic range is $1,000 to $3,000. If the drywall and insulation come out, containment goes up, and the fan is replaced and vented outside, the cost can move toward the upper half of that range. If the growth is surface only, the moisture source is a failed fan, and the drywall stays, it can sit in the lower half.

Five factors besides square footage move a quote:

  1. Whether the moisture source is already fixed. Remediation on an active leak is temporary work.
  2. Access. An attic air handler behind a low roof pitch costs more than a bathroom vanity.
  3. Material. Porous materials (drywall, insulation, cabinet board, carpet) usually come out. Tile, metal and glass can be cleaned.
  4. Containment. Negative air machines, plastic and a decontamination chamber are real line items.
  5. Clearance. Post-remediation verification adds a fee and records the result for the owner or landlord.

The full breakdown, including insurance, permits and a quote checklist, is on the mold removal cost page. There is also a size and cost checker that applies the national per-square-foot range to your own number.

Cost checker, short version

sq ft
Where is it

Estimated range

$1,000 to $3,000

Arithmetic on national per-square-foot figures: 100 sq ft × $10 to $30 per sq ft.

EPA line Above about 10 square feet, go straight to a removal scope and use clearance testing after the work. EPA guide (opens in a new tab)

Open the full cost checker and price tables

Source: cost page, Cost by square footage ($10 to $30 per square foot, national cost guides) and Cost by area of the home.

Get a call back

08 / Compare

Testing versus removal

Testing and removal answer different questions. Testing tells you whether growth is present, what the dominant genera are, and whether the space is clean after work. Removal is the physical work: containment, removal of affected material, cleaning, drying, and verification.

Testing or removal

Which one do you need?

Start here

If you can see it and it is bigger than a dinner plate, you need a removal scope, not more testing.

Mold testing and mold removal compared
QuestionMold testing and inspectionMold removal and remediation
What it answersIs there growth, where is the moisture, what is airborneHow much material is affected, how it comes out, how it is contained
When it makes senseMusty smell, no visible growth, a purchase, a move-in, a clearance checkVisible growth larger than about 10 sq ft, a recent leak, failed clearance
What you getMoisture mapping, air or surface samples, lab reportScope of work, containment, removal, drying, cleaning, clearance
Cost basisInspection fee plus lab fees per samplePer square foot, per room, or a project price

If you have just had a leak repaired and want proof the space is clean, you need clearance testing.

A useful rule: if you can see it and it is bigger than a dinner plate, you need a removal scope, not more testing. If you cannot see it but you can smell it, you need moisture mapping and, sometimes, air sampling. If you have just had a leak repaired and want proof the space is clean, you need clearance testing. It records the state of the space after the work.

The mold testing page covers sampling methods, lab turnaround and clearance in more detail. The removal versus remediation guide explains why the words are not interchangeable.

Lab report

How to read a lab report

A mold lab report looks more precise than it is. The numbers are estimates from a small sample, and no federal limits have been set to compare them against. What the report can do is tell you which genera are present, whether the indoor sample looks like the outdoor sample, and whether a space looks clean after work.

Four fields matter most:

FieldWhat it meansWhat it does not mean
Total spore countThe estimated spores per cubic meter in that sampleA pass or fail number
Outdoor controlThe baseline the indoor sample is compared withProof that indoor air is safe
Dominant generaWhich molds are most common in the sampleWhich one is causing a symptom
Detection limitThe smallest count the method can resolveThat a zero result is a clean room

A report that lists a genus without a location, a method and a detection limit is hard to use.

Lab results are also not portable between methods. A spore trap count and a culturable count are not the same measurement, and comparing them side by side is a mistake. Pick the method that answers the question, then compare like with like.

09 / Before and after

From the stain you see to a cleaned wall

Drag the line. Left is what a wall can look like when you find it. Right is the same kind of wall after contained, HEPA cleaning.

Before and after

Worker in a white suit and pink respirator vacuuming dark mold from an opened wall cavity beside a sliding glass door, a dark HEPA vacuum at the leftDark mold spots along the bottom of a beige wall beside a sliding glass door, wet pavement outside and a sofa with a throw at the left

Two stages of a mold job. Left: What you see. Right: Containment and HEPA cleaning.

Get a call back

10 / Local data

Tempe by the numbers

Tempe is not a suburb of single-family houses with the same profile as Gilbert or Queen Creek. It is a rental city with an old core. Almost six in ten occupied homes are rented, about four in ten housing units were built before 1980, and more than four in ten sit in buildings with five or more units (US Census ACS 2024 5-year estimates). Those three facts explain most of the mold work here.

Tempe by the numbers

  • Occupied homes that are rented57.7%

    Almost six in ten.

  • Housing units built before 198041.2%

    About four in ten.

  • Homes in buildings with 5 or more units41.8%

    More than four in ten.

Compare with

Median owner-occupied home value

$455,400

Tempe city, ACS 2024 5-year estimates.

Source: U.S. Census Bureau, American Community Survey, 2024 5-year estimates, Tempe city.

Get a call back

What this means in practice:

  • 01

    A rental turnover is a mold inspection window.

    When a tenant moves out and the unit sits closed for two weeks in July, a slow leak under the kitchen sink can bloom across a cabinet base before the next walkthrough.

  • 02

    Houses built before 1980 can have details that trap water

    cast iron drains that crack, copper supply lines that pinhole, original bathroom fans that vent into the attic instead of outside, and flat or low-slope roof sections that pond during monsoon.

  • 03

    Condos and apartments share walls, plumbing chases and roof assemblies

    A leak in one unit can surface as a stain in the unit next door.

The ACS 2024 five-year median owner-occupied value was $455,400, so a $3,500 remediation is not a trivial line item. It is also not a reason to live with the problem. The EPA's guidance is to fix the water first, and it says that in most cases sampling is unnecessary when visible mold growth is present.

11 / Renters and owners

Renters, landlords and HOAs

Tempe has a large rental population, and the first question after "is it mold" is usually "who pays for this". The short answer is that it depends on the cause and the lease, not on who noticed it first.

Which one are you?

I rent

You see it, the landlord controls the repair. Put it on paper first.

  1. 01

    Photograph it

    Take wide and close photos with something for scale, and note the date.

  2. 02

    Write to the landlord

    Send a dated message to the landlord or property manager that names the room and the moisture source. Keep a copy.

  3. 03

    Photograph it again after the repair

    If growth returns in the same spot, the before and after pair shows the source was not fixed.

General information, not legal advice. The lease and the cause of the water decide who pays.

Arizona's fit and habitable statute, A.R.S. 33-1324, requires a landlord to keep the premises fit and habitable. The word mold does not appear in that section. A common first step is documentation: photograph the growth with something for scale, note the date, write to the landlord or property manager about the moisture source, and keep a copy of the message.

For landlords, the turnover checklist matters more than the complaint log. Look under every sink, behind the toilet, at the base of the water heater, around the AC air handler, and on the ceiling below the roof line. A basic moisture meter from a hardware store can show what a visual walkthrough misses.

For HOA boards and condo owners, the governing documents decide who handles what. The association usually owns the common elements and the roof or building envelope. The owner usually owns the interior. Mold that starts in a shared wall or a common pipe is a board conversation, and the paper trail should start with the association's maintenance request process.

More detail on the rental path is on the rental and apartment mold page, with separate guides for tenants, landlords, students near ASU, neighbor units and HOA responsibility.

12 / Do it yourself

Do it yourself or get a call back

The EPA's guidance is the most useful line in this whole subject: if the moldy area is smaller than about 10 square feet, a homeowner can usually clean it up, provided the water or moisture problem is fixed first. Above that, the agency refers readers to its remediation guidance for larger jobs. A small patch on a bathroom ceiling is a cleaning job. A 4 by 8 foot section of drywall behind a leaking shower valve is a demolition and drying job.

Drying clock

024487296

Water started

30 hours ago

  1. Hour 0 to 24Extract standing water, move furniture, start air movement and dehumidification. Document everything with photos.
  2. Hour 24 to 48Measure moisture content in the drywall, baseboards and framing. If the readings are still high, drying equipment needs to stay or the material needs to come out.
  3. After 48 hoursAssume porous material that stayed wet is colonized until proven otherwise. A moisture meter and a visual check decide. In a Tempe summer, a closed house can push the timeline faster.

The EPA's guidance is to dry water-damaged areas and items within 24 to 48 hours. EPA, A Brief Guide to Mold, Moisture and Your Home (opens in a new tab)

Get a call back

Three numbers from the EPA guide worth writing down:

  • Dry water-damaged areas and items within 24 to 48 hours.
  • Keep indoor humidity below 60 percent, ideally between 30 and 50 percent.
  • Fix the water source before you treat the mold, or the mold comes back.

Bleach is not a remediation plan. The EPA says biocides such as bleach are not recommended as a routine part of mold cleanup, and the moisture problem is still there afterward. If the drywall or the cabinet base is soft, the material may need to come out.

If you rent, do not start with a bucket of bleach and a scrub brush. Clean the visible surface if it is small, photograph it, and put the moisture question in writing to the landlord or manager. If the growth is larger than a dinner plate, or it keeps returning in the same spot, that is a building problem, not a housekeeping problem.

13 / Why us

Why choose Mold Removal Tempe?

Three things to know before you send the form.

  • 01

    Licensed contractors only.

    Every Tempe mold job is done under an active Arizona ROC license.

    How to check a license
  • 02

    License checked first.

    We check the Arizona ROC license before a Tempe mold job starts.

    The 3 license steps
  • 03

    Start your quote.

    We will call you back shortly.

    Get a call back
  • 04

    Local coverage.

    We serve Tempe and the towns around it, from Broadmor and Maple-Ash to Mesa, Chandler and Scottsdale.

    See every area
  • 05

    Numbers with a source.

    The prices on this site are national ranges, each with its source named.

    Read the cost page

14 / The rules

Arizona rules that affect the job

Arizona contractor licensing generally applies when the labor and materials for a project exceed $1,000, or when the work requires a permit. Work that involves removing drywall, insulation or cabinetry, and rebuilding afterward, can cross that line.

The Arizona contractor license page explains how licensing works in the state.

Man in a navy shirt holding a tablet talks with a woman on the walkway of a brick ranch house with a shade tree and a gravel yard
Check an Arizona contractor license

Insurance

Insurance: what to expect from the claim process

Homeowners insurance sometimes covers mold, and sometimes does not. The difference is usually the cause. A sudden, accidental discharge from a supply line is treated differently from long-term seepage or a maintenance item that was left alone. Only the policy and the insurer can say what is covered.

What the process usually looks like:

  1. Stop the water and document everything with photos and dates.
  2. Call the insurer and open a claim before demolition, unless there is an immediate safety issue.
  3. Ask the adjuster what documentation they want: moisture readings, lab results, scope, photos.
  4. Get the remediation scope in writing before work starts, with the moisture source and the clearance step named.
  5. Keep receipts for any emergency drying or repairs.

If the cause is a roof leak from monsoon season, the conversation often turns on maintenance. If the cause is a failed supply line, it often turns on sudden and accidental damage. Either way, the paperwork starts with the moisture source, not the mold.

15 / Through the year

A Tempe mold calendar

The monsoon dates come from the National Weather Service Phoenix office. The rest is the pattern that shows up in Tempe housing, not a prediction for any one property.

  1. 01

    Monsoon, June 15 to Sept 30

    Wind-driven rain finds roof seams, window flashing and stucco cracks

    Where to lookCeilings, attic sheathing, walls under windows

  2. 02

    Peak summer

    AC condensate lines clog, drain pans overflow, swamp coolers cycle hard

    Where to lookAttic air handlers, closet pans, ceiling stains near vents

  3. 03

    Winter

    Water heaters and supply lines fail, guests close up rooms

    Where to lookWater heater closets, under sinks, exterior walls

  4. 04

    Year-round

    Slab leaks, slow toilet flanges, dishwasher and ice maker lines

    Where to lookBaseboards, cabinet bases, carpet edges

16 / Keep it clean

After remediation: how to keep it from coming back

The work is only half the fix. The other half is the routine that keeps moisture from returning.

Teal dehumidifier running in a living room with the lower wall opened at the baseboard, a sofa with patterned pillows and a framed desert print
  • Fix the source, then verify it. A roof repair should be checked at the next rain. A plumbing repair should be checked with a moisture meter after a week.
  • Keep indoor humidity between 30 and 50 percent. The EPA's upper bound is 60 percent. A cheap hygrometer is enough to know where the house sits.
  • Run the bathroom fan during and after every shower. If the fan vents into the attic, fix the duct. A fan that moves air into the attic is moving the problem, not solving it.
  • Clear the AC condensate line before summer. A clogged condensate line is a common cause of overflow into a closet or a ceiling.
  • Check the water heater pan and the sink supply lines. Look under every sink at least once a year, and at every tenant turnover.
  • Walk the attic after monsoon. Look at the sheathing around vents, flashing and the air handler platform. A brown ring is cheaper to fix in September than in July.
  • Keep the clearance report. It is the document that shows the space was clean, and it matters at resale, at lease signing and at the next insurance conversation.

Prevention is not a product. It is a short list of checks that most people skip until something leaks.

Health

Mold and health: what the sources say

The EPA's guide is careful about health claims. Mold can cause allergic reactions and can trigger asthma in sensitive people. Some people have no reaction at all. No EPA or other federal limits have been set for mold or mold spores.

What that means in practice:

  • If someone has symptoms, the first call is a doctor, not a remediation company.
  • If a doctor wants environmental information, a moisture inspection and a lab sample can help, but they are not a diagnosis.

The EPA's guidance is about moisture, not fear. Fix the water, remove the growth, dry the structure, and keep indoor humidity in the 30 to 50 percent range. That is the part that can be controlled.

17 / Service area

Areas covered

We serve Tempe and the towns around it. Tempe neighborhoods first, then the Valley cities.

All 34 areas

Tempe is covered neighborhood by neighborhood, along with the cities around it. A 1960s rental near ASU and a newer house in Warner Ranch have different mold problems, so each area has its own housing numbers.

18 / Guides

Tempe mold guides

Short answers to the questions that come before a quote. Pick the topic that fits.

All 23 guides

These are the questions that come before a quote: what to do first in a rental, what a landlord should check between tenants, how monsoon roof leaks turn into attic mold, what not to put on mold, and how long remediation actually takes.

CostMold removal cost in Tempe: ranges, the size checker and a quote checklist

19 / 10 questions

Frequently asked questions

Still have a question?

Send the form. Someone from our team will call you back soon.

Get a call back

Q.01

How much does mold removal cost in Tempe?

National ranges run about $1,500 to $9,000 for remediation, with an average near $3,500 and small bathroom jobs starting around $500. One national cost guide puts per-square-foot pricing at $10 to $30. Tempe quotes depend on access, containment, material removal and whether the moisture source is fixed. The cost page has the full table.

Q.02

Is professional mold removal worth it?

The EPA says a moldy area under about 10 square feet can often be handled by a homeowner once the moisture source is fixed, and it refers readers to separate remediation guidance for larger areas. The deciding factor is usually the water, not the size of the stain.

Q.03

Can I remove mold myself?

The EPA says a moldy area under about 10 square feet is usually a homeowner job. You still need to fix the leak, wear protection, and dry the area within 24 to 48 hours. If the material is soft, the growth keeps returning, or the area is larger than a dinner plate, it is a remediation scope.

Q.04

What kills mold permanently?

Nothing kills mold permanently if the moisture stays. The permanent fix is removing the water source, removing colonized porous material, cleaning the rest, and keeping indoor humidity below 60 percent. Cleaning products address the surface; they do not address the reason it grew.

Q.05

What should I not put on mold?

Do not paint or caulk over it, do not cover it with furniture or a new cabinet base, and do not use bleach on porous material as a substitute for removal. Paint can hide the problem without fixing the moisture behind it.

Q.06

Can black mold be remediated?

Yes. "Black mold" usually refers to Stachybotrys chartarum, but several genera look black. The steps are the same as for other mold: fix the moisture, contain, remove porous material, clean, dry, verify.

Q.07

What is the difference between mold removal and mold remediation?

Removal is the physical removal of growth and affected material. Remediation is the whole process: assessment, containment, removal, cleaning, drying and verification. Removing visible growth without the moisture and clearance steps covers only part of the process.

Q.08

How much does a mold inspection cost?

One national cost guide reports $450 to $800 for an inspection with lab testing, with an average near $500 for a 2,500 square foot home and two samples, and the rounded national range is about $300 to $1,000. Inspection is usually priced separately from remediation, and clearance testing is a separate step. The testing page explains what each sample type answers.

Q.09

Are mold inspections worth it?

They are worth it when you cannot see the growth but can smell it, when you are buying or renting a property, or when you need clearance after remediation. They are less useful when visible growth already tells you what to do. In that case, spend the money on removal and clearance instead.

Q.10

Does Arizona have a mold problem?

It can. Arizona is dry, so mold here is often tied to a specific water event: a monsoon roof leak, an AC condensate line, a swamp cooler, a slab leak, or a supply line. A musty smell in July is worth checking.

White cargo van with its rear doors open in a driveway, a man in navy work clothes wheeling a teal air machine out in front of a ranch house

Form open 24/7

Get a call back about mold in your home

Send the form. Someone from our team will call you back soon.

Mold in the house?Get a call back

Before you go: want a call back?

Send the request form and someone will call you back about the mold.

Get a call back

Get a call back

Send the form and someone from our team will call you back.